Results 1 to 8 of 8

Thread: 10lbs of boost???

  1. #1
    Inactive Member SiMike's Avatar
    Join Date
    April 8th, 2001
    Posts
    48
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    i have a 99 civic si,jrsc w/6psi pully, kamikazi header,strait pipe,3"thermal exaust,3" short ram intake,walboro fuel pump and apexi v-afc. i was wondering why my boost gauge was reading 10lbs at WOT???? could my boost gauge be hooked up wrong? it used to read 12psi before the exhaust. i don't have any restrictions that would cause higher boost,so if you could help me out....thanks....

  2. #2
    Inactive Member registry's Avatar
    Join Date
    May 17th, 2000
    Posts
    176
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    aa

  3. #3
    Inactive Member phicycle's Avatar
    Join Date
    February 12th, 2001
    Posts
    87
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Maybe you got one of the "good" eaton blowers that TOO talks about. There's supposed to be a lot of variation between the performances of their production line blowers.

  4. #4
    Inactive Member cetane's Avatar
    Join Date
    January 16th, 2001
    Posts
    176
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Im in the same boat man. I have an 8psi pully and it says Im at 11 psi at wot, so who knows. I would just be sure you take the advice of others and think about the safety of your motor as if you were going to add more boost.

  5. #5
    Inactive Member phicycle's Avatar
    Join Date
    February 12th, 2001
    Posts
    87
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    If the pulley is for 8 psi with a GSR, it's going to produce substantially more on a 1.6 liter engine. You have to take displacement into account.

  6. #6
    Inactive Member 88 SC CRX Si's Avatar
    Join Date
    December 9th, 2000
    Posts
    51
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Might want to check out this post.....

    http://www.hostboard.com/ubb/Forum40/HTML/005233.html

    -Ryan-

    ------------------
    "Noth'in like Induction..."

    88' CRX Si - JRSC @ 6psi
    Endyn/Bosch FP, CarTech FMU, B&M CommandFlo
    AutoMeter - Phantom FP, A/F, Boost gauges & pods, B&M FP Set
    Eibach Pro-Control Bars, ARP Head Stud Kit, AEM Pads

  7. #7
    Inactive Member SiMike's Avatar
    Join Date
    April 8th, 2001
    Posts
    48
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    how would i have gotten a gsr pully??? a mistake by jr?? if i was truly running 10lbs wouldn't i be detonating badly since i have no water injection or NOS? i checked my plugs for metal chips or anything unusual and they look fine. maybe i shouldn't worry about it. it could be that the gauge is off. it's an autometer boost gauge.... thanks for the input....

  8. #8
    Inactive Member lostsol's Avatar
    Join Date
    April 23rd, 2000
    Posts
    55
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    i have a del sol with a b16 swap in it. i am running the 8 psi pulley on my blower. the average boost numbers i see are 9 and sometimes 10. i did see it go to 11 twice. i am at about 13 degrees of timing and not the first hint of detonation. i also have no a/c and no power steering. i dont know if that helps but there ya go. smile

    stacie

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •